WPX1/WPX1C Tube type selection
Tube type selection
Scroll Table
| Tube type | Product Description | Regulately compliance/meets |
|---|---|---|
PHARMED BPT |
*Great resistant to general chemicals, acid, alkali and oxidizing agents *Compatible with virtually all commercial cleaners and sanitizers *Lasts up to 30 times longer than silicone tubes. |
USP Class VI |
| Tygon Chem A-60-G (Tygon A-60-G)  |
*Thermoplastic elastomer (TPE) tube for industrial use *Good resistant to general chemicals as TPE tube |
- |
| Tygon Food A-60-F (Tygon A-60-F)  |
*Thermoplastic elastomer (TPE) tube for food, dairy and sanitary industries *Good resistant to general chemicals as TPE tube |
NSF 51 3-A |
Tygon 3355/3350 |
*High-performance and platinum-cured silicone tube *Ultra-smooth inner bore reduces potential for particle entrapment *Excellent fluid flow characteristics. |
FDA 21 CFR Part 177.2600 USP Class VI S 3-A (3350 only) |
| Versilon F-5500-A (FLURAN F-5500-A)  |
*A proprietary fluorelastomer tube *Exellent resistance to corrosive chemicals, oils, fuels and solvents *Ozone and UV Light resistant |
- |
| Versilon 2001 (TYGON 2001)  |
*Plasticizer-free chemical resistant tube. *Great resistant to a wide range of fluids that typically destroy PVC products *Applicable to soap and detergent dispensing, ink transfer, water purification lines, food, beverage and chemical transfer |
FDA 21 CFR Part 177.2600 |
| Tygon Lab E-LFL (Tygon S3 E-LFL)  |
*Non-DEGO tube for laboratory, Food & Beverage and Biopharmaceutical Applications *Longest flex life in any clear Tygon tubes *Extremely low particle spallation for sensitive fluid applications |
FDA 21 CFR Part 177.2600 USP Class VI NSF-51 EU 10/2011 |
| Tygon Food XL-60 (Tygon XL-60)  |
*Alternative to silicones and PVC when longer pump tube life is required *Excellent resistance to a wide range of fluids, including acids and bases *Greatly reduce the risk of fluid contamination |
FDA 21 CFR Part 177.2600 NSF 51 EU 10/2011 |
W TUBE |
*Dual-wall tube which has excellent resistant to chemicals, acid, alkali. *Inner layer: Polyolefin Outer layer: Thermoplastic Elastomers |
- |
Note: Tygon, Versilon, Pharmed and Fluran are manufactured by Saint-Gobain Group.
Please refer to chemical resistant properties for tube selection. It is the user’s responsibility to ensure the suitability and safety of tube for all intended uses, including establishing the compatibility of any fluid with the tubing through which it is transmitted. Laboratory, field or clinical tests must be conducted in accordance with applicable requirements in order to determine the safety and effectiveness for use of tubing in any particular application. If intended for medical use, it is the user’s responsibility to ensure that the tubing to be used complies with all applicable medical regulatory requirements.
Tube size and number of rollers selection
Scroll Table
| Size code |
1/16 |
3/32 |
1/8 |
3/16 |
||||
|---|---|---|---|---|---|---|---|---|
| Inner diameter |
1.6mm (1/16”) |
2.4mm (3/32”) |
3.2mm (1/8”) |
4.8mm (3/16”) |
||||
| Available tube material |
P / NF |
S / P / NF |
All type (of) |
ALL type except for U |
||||
| Number of rollers/code |
2/4 |
2/4 |
2/4 |
2/4 |
||||
| Number of rollers | 2 | 4 | 2 | 4 | 2 | 4 | 2 | 4 |
| Flow amount per rotation (ml) | 0.17 | 0.15 | 0.35 | 0.3 | 0.6 | 0.5 | 1.2 | 0.9 |
Caution: Tube type EL1/8", F3/16" cannot be used with four rollers due to its high hardness.
Note.
1. The flow amount rotation is based on laboratory test at WELCO. This may vary depending on operating environment, lot tolerances, and other factors. Please veryfiy performance under actual operation conditions.
2. The reference flow rate of the pump is determined by the product of flow amount per rotationand motor speed.
